Job Information
Menzies Aviation Lead GSE Mechanic in Cleveland, Ohio
Description
Responsible for leading and directing the activities of other GSE mechanics. Also does the work of a mechanic as required.
Location: Cleveland-Hopkins International Airport (CLE)
Schedule: 40 hours a week with two consecutive days off depending on the operational needs of the shop.
Hourly Rate: $34.00
Required: Must possess mechanical tools and toolbox
MECHANICAL DUTIES
All duties listed under GSE 1,2 and 3.
Leadership Training
Advanced trouble shooting.
The ability to operate diagnostic equipment.
The ability to read schematics (electrical, air, hydraulic).
Verify that vehicles and equipment can pass appropriate safety inspections.
Maintain repair and service all aspects of all vehicles and equipment.
Determines the need and extent of repair work required on vehicles and equipment based on operator’s reports and testing equipment.
Assist in instructing Mechanic 2 on work procedures applicable to their respective level.Inspects and approves work of Mechanic 2.
Performs other duties as assigned or requested.
Completes required documentation and performs data entry.
Lead GSE team in all aspects of GSE business group.
EQUIPMENT TYPES
All equipment types listed under GSE 1 and 2
Ground power unit
AC/Heat cart
Airstart
Lower deck loader
Main deck loader
Hydrant cart (narrow and wide body)
Refuel tanker (all size and fuel types)
Deicers
Cater truck
Hi lift truck
Hydrant truck
Towbarless push back
Transport trailer (fuel and cargo)
MINIMUM QUALIFICATIONS
Vocational/ Specialized Training.
Experience operating diagnostic equipment.
Certification from a recognized program, preferred.
5 years experience in automotive/ mechanical work.
Requires a Valid Driver’s License.
GSE Lead Technician - Tool Requirements
1/2” DRIVE
RATCHET
SWIVEL
SOCKETS (DEEP AND SHALLOW REQUIRED)
BREAKER BAR
EXTENSIONS 3”, 6” AND 12”
STANDARD 3/8”-1 ½“
METRIC 14MM-24MM
6” IMPACT EXTENSION
DEEP IMPACT SOCKETS ½”-1 ½”
ADAPTOR ½” - ¾”
WRENCHES
COMBINATION WRENCHES ¼”-1 ½”
METRIC COMBINATION WRENCHES 8MM-24MM
ALLEN WRENCHES 1/16”-3/8”
METRIC ALLEN WRENCHES 2MM-12MM
CRECENT WRENCHES 8”,12”, 15”, AND 18”
HAMMERS, CHISELS, PUNCHES
BALL PEEN HAMMER 16 oz
BALL PEEN HAMMER 32 oz.
4 POUND SLEDGE
PUNCH AND CHISEL SET
CENTER PUNCH
MISC FILE SET
THREAD CHASER
1/4” DRIVE
RATCHET
SWIVEL
SOCKETS (DEEP AND SHALLOW REQUIRED)
STANDARD 1/8”-9/16”
EXTENSIONS 3” AND 6”
METRIC 5MM-14MM
3/8” DRIVE
RATCHET
SWIVEL
EXTENSIONS 3”, 6” AND 12”
SOCKETS (DEEP AND SHALLOW REQUIRED)
STANDARD 5/16”-1”
METRIC 8MM-21MM
SPARK PLUG SOCKETS 5/8” AND 13/16”
SCREWDRIVERS and PRY BARS
PHILLIPS HEAD SCREWDRIVERS #1, #2, #3 AND STUBBY
STANDARD HEAD SCREWDRIVERS #1, #2, AND STUBBY
PRY BARS 12”, 24”, AND 36”
1/2” DRIVE IMPACT GUN
3/8” DRIVE IMPACT GUN
DIE GRINDER
OSHA APPROVED AIR NOZZLE
TIRE CHUCK
1/2” AIR DRILL
3/8” AIR DRILL
1/4” AIR RATCHET
3/8” AIR RATCHET
PLIERS
STANDARD PLIERS 8”
NEEDLE NOSE PLIERS
CHANNEL LOCKS 12” AND 15”
BRAKE SPRING PLIERS
WIRE STRIPPERS
WIRE CRIMPERS
WIRE CUTTERS
DIAGNOL CUTTERS
SLIP JAW PLIERS
VICE GRIPS 7” ,10”, AND 12”
JUMPER WIRES (2 SETS)
TEST LIGHT 12 AND 24 VOLT
DIGITAL VOLT METER (FLUKEMETER OR EQUIVELANT)
FLASHLIGHT
FEELER GUAGE SET
SPARK PLUG GAPPING TOOL
FUSE PULLERS-AUTOMOTIVE
FUSE PULLERS-NON CONDUCTIVE A/C, HIGH VOLTAGE
BRAKE ADJUSTING SPOONS
TIRE PRESSURE GUAGE (UP TO 120 PSI)
TIRE VALVE STEM/CORE TOOL
O-RING PICK SET/SCRIBE
INSPECTION MIRROR
SNAP RING PLIERS SET
TAPE MEASURE (25’)
OIL FILTER WRENCHES (SMALL, LARGE)
WIRE BRUSH
GLOVES
LARGE LOCKING ROLLAWAY TOOL BOX
SMALL LOCKING ROAD BOX
PHYSICAL DEMANDS
The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.
While performing the duties of this job, the employee is frequently required to stand; walk; sit; use hands to finger, handle, or feel objects, tools, or controls; reach with hands and arms; climb or balance; stoop, kneel, crouch, or crawl; and talk or hear. The employee must frequently lift and/or move up to 25 pounds.
WORK ENVIRONMENT
The work environment characteristics described here are representative of those an employee encounters while performing the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.While performing the duties of this job, the employee regularly works in outside weather conditions.
The employee frequently works near moving mechanical parts and in high, precarious places and is frequently exposed to fumes or airborne particles, risk of electrical shock, and vibration. The employee is occasionally exposed to toxic or caustic chemicals. The noise level in the work environment is usually very loud.
Equal Opportunity Employer/Protected Veterans/Individuals with Disabilities
The contractor will not discharge or in any other manner discriminate against employees or applicants because they have inquired about, discussed, or disclosed their own pay or the pay of another employee or applicant. However, employees who have access to the compensation information of other employees or applicants as a part of their essential job functions cannot disclose the pay of other employees or applicants to individuals who do not otherwise have access to compensation information, unless the disclosure is (a) in response to a formal complaint or charge, (b) in furtherance of an investigation, proceeding, hearing, or action, including an investigation conducted by the employer, or (c) consistent with the contractor’s legal duty to furnish information. 41 CFR 60-1.35(c)